Computer problems keep getting message?

Question

My computer will not come on this is the error message i get, cannot get into the safe mode. What should i do. Tried to restore it will not let me do that either...any suggestions. Thanks in advance.

A problem has been detected and windows has been shut down to prevent damage to your computer.

If this is the first time you’ve seen this stop error screen, restart your computer. If this screen appears again, follow these steps:

Check to be sure you have adequate disk space. If a driver is identified in the stop message, disable the driver or check with the manufacturer for driver updates. Try changing video adapters.

Check with your hardware vendor for any BIOS updates. Disable BIOS memory options such as a caching or shadowing. If you need to use safe Mode to remove or disable components, restart your computer, press F8 to select Advanced start up options, and then select safe mode.

Technical information:

*** STOP:0x0000008E (oxC0000005, 0xF1D5E86E, OxEF665650, 0x00000000)

*** CMDMON.sys- Address F1D5E86E base at F1D5E000, DateStamp 4 5bc9111

Beginning dump of physical memory dump complete

Physical memory dump complete

Contact your system administrator or technical support group for futher assistance.

Answer 1

people with these Qs should allow email..its step by step..got xp?

Answer 2

"STOP 0x0000008e" error message during Windows XP setup

View products that this article applies to.

Article ID : 315335

Last Review : May 27, 2004

Revision : 3.2

This article was previously published under Q315335

SYMPTOMS

When you install Microsoft Windows XP, you may receive a Stop Error message that is similar to one of the following while the Setup program is running:

STOP 0x0000008e

STOP 0x00000050 PAGE_FAULT_IN_NON_PAGED_AREA

Additionally, if you troubleshoot by removing all unnecessary hardware devices that are installed on the computer, and then you run the Setup program, you may receive an error message that is similar to the following:

Setup cannot copy the file Setupdd.sys.

Back to the top

CAUSE

This behavior may occur if one of the following conditions is true: • One or more of the random access memory (RAM) modules that are installed on your computer are faulty.

• The RAM configuration is incompatible with Windows XP.

Back to the top

RESOLUTION

To troubleshoot this behavior, follow these steps: 1. Remove some of the memory modules that are installed on the computer. Leave at least the RAM that is required for the computer to start and run Windows XP.

The recommended RAM to run Windows XP is 128 megabytes (MB). The minimum is 64 MB, and the maximum is 4 gigabytes.

For example, if two 256-MB memory modules are installed on your computer, remove one of the memory modules.

2. Restart your computer, and then run the Setup program:a.  Insert the Windows XP Setup CD-ROM in the CD-ROM drive, start the computer, and then click OK to select the first option screen to install a copy of Windows XP.  

b.  Click Accept, and then follow the instructions on the screen to complete the Windows XP installation.



3. If you again receive the error message that is mentioned in the "Symptoms" section, go to step 4.

4. Remove a different memory module, or install the RAM in a different memory slot.

5. Restart your computer, and then rerun Setup.

You may have to restart your computer several times to identify the specific memory modules that are not working correctly.

Back to the top

MORE INFORMATION

For information about how to add and remove RAM, contact the manufacturer of your computer or see the documentation that is included with your computer.

For additional information about the Windows XP Setup program, click the following article numbers to view the articles in the Microsoft Knowledge Base:

306824 (http://support.microsoft.com/kb/306824/) Release Notes for Windows XP Setup contained in the Home.txt file

286463 (http://support.microsoft.com/kb/286463/) Release notes for Windows XP Setup contained in the Pro.txt file

286647 (http://support.microsoft.com/kb/286647/) Windows XP Read1st.txt file contents

For information about how to contact your hardware vendor, visit the following Microsoft Web site:

http://support.microsoft.com/gp/vendors (http://support.microsoft.com/gp/vendors)

Microsoft provides third-party contact information to help you find technical support. This contact information may change without notice. Microsoft does not guarantee the accuracy of this third-party contact information.

Back to the top

--------------------------------------...

APPLIES TO

• Microsoft Windows XP Professional

• Microsoft Windows XP Home Edition

Back to the top

Keywords:  kberrmsg kbenv kbprb KB315335

Back to the top

  You need to troubleshoot your RAM. Did you just build your PC? or have you done anything to your RAM? I simply put your Stop Code into the search engine and it came back with a Microsoft Knowledgebase Article on your failure. It points to bad RAM (memory). The article tells you how to troubleshoot the problem.

Cheers

Answer 3

This is going to be a major problem for you.  This particular BSOD is caused by a virus in the Master Boot Record (MBR) which is the first part of the partition on your hard drive.  There is only one way to fix the MBR, and that is to replace it:

http://ultcomprepair.blogspot.com/2008/0...

The problem is that you're probably going to get the same BSOD when trying to repair the MBR (it happens 9/10).  I've got a computer I'm working on right now with the same problem.

In the end the best course of action here is to do a full recovery on the system.  There is nothing that can be done.  It's annoying but generally the only hope.

EDIT: Depending on the computer and how long ago your purchased the computer there might be a built in partition.  Problem is that with an MBR virus it might not work.  If you know the make and model though I can help you.