Do you know how to make a DIY windmill?

Question

The kind that produce electicity. It would have to be smaller than five feet. Are there any sites that tell me? I would want to conect it to only a certain part of our house and I don't know how to wire stuff like that. If you don't know please answer though so you can give me ideas.

Thanks.

Answer 1

wind mills

are for milling

it is why they are called wind mills

you want a wind generator

hook a propeller up to a turbine

and lead it to a battery

check Huddler for the latest in green technology

http://greenhome.huddler.com/products/

Answer 2

Let me start off by saying we (my family and I) live completely, 100% “off of the grid and are completely self sufficient”

There are no utility lines, no water lines, no roads, tv, cell service, etc. on our ranch. EVERYTHING needed is produced here. All electricity comes from 27 solar panels, 2 main wind gens and a back hydrogen generator if needed (typically we can last 9 days with all luxuries of sunless windless weather, hasn't happened yet). Water is caught and storaged from the rain. Hot water is made with solar batch water heaters with an on-demand hydrogen hot water heater as backup. solar chimney, solar AC, solar heating, solar water heating (pool and home), solar stove, solar power, wind power, hydrogen powered back up generator, hydrogen back up water heater, hydrogen stove, 2 hydrogen powered trucks, 1 EV (electric vehicle) and satellite internet. Even our vehicles use alternative energy (2 hydrogen trucks, 1 EV electric vehicle converted). Because of this we have no bills, no debt and no mortgage.

Anyone interested can check it out at..

www agua-luna com

Electricity from the wind is one of the simplest forms of alternative energy. i've personally built over a dozen wind gens and currently run all my electrical needs off of 2 wind turbines and a couple dozen home made solar panels.

Basically think of the little motor in your car (the alternator), but insted of it being turned by a belt driven by your car's engine powerd gas, it's turned by the wind.

I offer a step by step DIY guide to walk anyone interested threw the process. You can find it at www agua-luna com or you can email me.

The fallowing steps were taking directly out of a DIY guide I offer to those who would like to run their homes on wind power safely, reducing their monthly utility bills or even selling power back the the electrical companies. The entire guide is available at www agua-luna com

"This manual is based on using a 260 VDC, 5 A continuous duty Treadmill Motor with a 6 inch threaded hub. These motors are available for under $50 from most motor surplus stores. We are getting about 7 amps in a 30 mph wind. In other words, it is a simple, cheap little machine to get you started.  "

"ASSEMBLY

1. Place the motor on top of the square tubing and bolt it in, using the two 5/16” x ¾” bolts.

2. Place the diode on the square tubing, about 2” behind the motor, and s***w it into position using the self-tapping metal s***w.

3. Connect the black wire coming out of the motor to the positive incoming terminal of the diode (Labeled AC on the positive side).

4. Connect the red wire coming out of the motor to the negative incoming terminal of the diode (Labeled AC on the negative side).

5. Center the tail over the square tubing, at the back end. Clamp your tail onto the side of the square tubing.

6. Using 2 self-tapping screws, s***w the tail in place.

7. Place each blade on the hub so that all the holes line up.  Using the ¼" bolts and washers, bolt the blades to the hub.  For the inner three holes, use two washers per bolt, one on each side of the blade. For the outer three holes, just use one washer next to the head of the bolt. Tighten.

8. Hold the end of the shaft of the motor (which comes through the hub) firmly with pliers, and turn the hub counterclockwise until it tightens and stops.

9. s***w the nipple tightly into the floor flange using a pipe wrench.

10. Clamp the nipple in a vice so that the floor flange is facing up and level.

11. Place the square tubing (and everything that is on it) on top of the floor flange and move it so that it is perfectly balanced.

12. Through the holes of the floor flange, mark the square tubing at the point of balance.

13. Drill these two holes using a 5/32" drill bit. You will probably have to take off the hub and tail to do this).

14. Attach the square tubing to the floor flange with two sheet metal screws.

For a longer life span of your wind generator, you should paint the blades, motor sleeve, mount and tail."

www agua-luna com

Hope this helped, feel free to contact me personally if you have any questions if you’d like assistance in making your first self sufficient steps, I’m willing to walk you step by step threw the process. I’ve written several how-to DIY guides available at  www agua-luna com on the subject. I also offer online and on-site workshops, seminars and internships to help others help the environment.

Dan Martin

Alterative Energy / Sustainable Consultant, Living 100% on Alternative & Author of How One Simple Yet Incredibly Powerful Resource Is Transforming The Lives of Regular People From All Over The World... Instantly Elevating Their Income & Lowering Their Debt, While Saving The Environment by Using FREE ENERGY... All With Just One Click of A Mouse...For more info Visit:  

www AGUA-LUNA com

Stop Global Warming, Receive

Answer 3

http://www.cat.org.uk/catpubs/pubs_conte...

Answer 4

You could ask the experts at this site about residential windmills:

http://www.discoverperfectenergy.com/dpe...

Answer 5

Check out "Homesteading Adventures: A Guide for Doers and Dreamers" It has a chapter about building windmills.

N.

http://badhuman.wordpress.com