Going to pro skate shop and getting skates molded to foot?

Question

So i was thinking about buying my own skates and taking some ice skating lessons. I don't know much about skates but i have heard that you can go to the pro shop at the rink and have them put them in a special oven to heat them so they can mold them to your foot, my question is does that cost money to do? if so, approximately how much?

Answer 1

Not all boots are heat moldable.  I think Riedells are pretty much the most popular brand that are, but that's only on some models.  They do typically perform that service at the shop since you and your feet are there and they can hopefully make them feel as good as possible. I don't think they charge for that service, since you purchased the boots from them.

As mentioned before, if you're just starting out, that type of boot might be a lot for you.  I highly recommend Riedells for beginners.  They have a wide range of boots for all levels, including boot/blade sets for beginners.  Skaters who wear them say they're pretty comfortable.  If you're just starting lessons, maybe try the Riedell blue ribbon.  It's a good skate with more ankle support than a recreational skate that will take you through a lot of the beginning levels, but it's not so stiff that it will cause you pain and be over-kill for what you're doing.  They're about $150 for boot and blade (more advanced boots and blades are sold seperately).  Buying a boot that is too stiff for your level can not only be painful, but it can be very difficult to break them in, which can cause problems for you phyiscally and in your skating improvement.

A pro shop with experience can fit you for skates and give you a brand/model recommendation.  Since boots all run differently -- small, narrow, wide, large -- it's possible that based upon your foot, they may recommend a certain brand for you and the level you're skating.  Same deal with blades....which do need sharpening prior to first use.  

Good luck!!!  :)

Answer 2

If you are just learning to skate don't do that. Start with at the most $100 skates new or some nice used ones (it sounds gross, but the shops clean and disinfect them). I recommend a Riedell. They come in different ribbons to determine the quality. I would do white or red to begin (for frequent recreational use to beginner figure skating).

Then if you know that you like it and want to do it for a while, get some nice Riedell gold or silver ribbon figure skates. They are from about $260-300.

If you get really competitive, then you can get the molded figure skates that can go to $400. Other then that, it's almost a waste of money.  

Answer 3

I am getting a pair at the pro shop next to my rink for about $140ish and heat molding is included when I buy my skates. I think it is a lot more comfortable when they are heat molded. The way heat molding works is they put it in a special oven and then you put the skate on and it will mold to your feet. If you have a bunion or something on your feet (like I do) they  can put special dents that will go out further. Hope I helped.

Answer 4

Usually, it'll be free. It was when I did it.

Answer 5

usually this comees with the price in your skates and they will tell you at the pro shop whether your skates need it or not

Answer 6

the brand your talking about is jackson skates not all pro skops do that for you i recomend oredering from riddel.com

here's my recomendations

http://www.riedellskates.com/ice/121.htm...

http://www.riedellskates.com/ice/117.htm...

http://www.riedellskates.com/ice/112.htm...

http://www.riedellskates.com/ice/110.htm...

its a fair price your beginer exactly the kinds you would need

Answer 7

only some skates are heat moldable. the skates that are heat moldable are generally at least 300 dollars for boots and blades, but at my pro shop they mold them for you for free once you buy the skates. however, those skates are for competitive skaters and not only do you not need them, but you would have trouble skating in them. just get a basic pair of skates. those generally aren't heat moldable but cost more around 80 dollars.

Answer 8

If you haven't skated much or taken lessons before then do not get those.  You have to buy the boots and blades separate most of the time, and the cheap ones for which that is done with are at least $400 for the set.  Also, even though they are better and cause less blisters/calluses/sores than the high quality skates from 10 years ago, they are still very tough on your feet if you've never skated before.

Try some regular but good quality beginner pairs on, make sure they support your ankle but not so much support that you don't feel like you don't have control over your own feet and ankles.  In most rinks the pro shop workers are pretty knowledgeable about what is needed for beginner through mid-level skaters, even if they specialize in hockey.

Answer 9

At the minimum of 400 dollars...I would suggest maybe getting some recreational skates ot something lyke that for about 50-80 dollars, it is a big waste of money to get real figure skates if u cant even skate yet. ( Not trying to sound mean)

Answer 10

if u are just starting don't. it is very expense, u can spend 200$ on a pair of skated without having them molded to your feet. if u are just skating it is better to get 2 hand skates that are all ready broken in and wouldn't hurt your feet as much