Question:

What is the 3 method of Radar contact..according to FAA?

by  |  earlier

0 LIKES UnLike

What is the 3 method of Radar contact..according to FAA?

 Tags:

   Report

1 ANSWERS


  1. Actually there's a bit more than that available, depending on primary target, secondary target, etc.  Please forgive me for taking the easy way with a cut and paste, but here it is, straight from the FAA ATC "bible" (FAA Order 7110.65S)

    5-3-2. PRIMARY RADAR IDENTIFICATION METHODS

    Identify a primary or radar beacon target by using one of the following methods:

    a. Observing a departing aircraft target within 1 mile of the takeoff runway end at airports with an operating control tower, provided one of the following methods of coordination is accomplished.

    1. A verbal rolling/boundary notification is issued for each departure, or

    2. A nonverbal rolling/boundary notification is used for each departure aircraft.

    NOTE-

    Nonverbal notification can be accomplished via the use of a manual or electronic "drop tube" or automation.

    b. Observing a target whose position with respect to a fix (displayed on the video map, scribed on the map overlay, or displayed as a permanent echo) or a visual reporting point (whose range and azimuth from the radar antenna has been accurately determined and made available to the controller) corresponds with a direct position report received from an aircraft, and the observed track is consistent with the reported heading or route of flight. If a TACAN/VORTAC is located within 6,000 feet of the radar antenna, the TACAN/VORTAC may be used as a reference fix for radar identification without being displayed on the video map or map overlay.

    NOTE-

    1. Establishment of radar identification through use of DME position information can be complicated by the fact that some military TACANs are not collocated with frequency-paired VORs and might be separated from them by as much as 31 miles.

    2. Visual reporting points used for RADAR identification are limited to those most used by pilots and whose range and azimuth have been determined by supervisory personnel.

    c. Observing a target make an identifying turn or turns of 30 degrees or more, provided the following conditions are met:

    NOTE-

    Use of identifying turns or headings which would cause the aircraft to follow normal IFR routes or known VFR flight paths might result in misidentification. When these circumstances cannot be avoided, additional methods of identification may be necessary.

    1. Except in the case of a lost aircraft, a pilot position report is received which assures you that the aircraft is within radar coverage and within the area being displayed.

    2. Only one aircraft is observed making these turns.

    3. For aircraft operating in accordance with an IFR clearance, you either issue a heading away from an area which will require an increased minimum IFR altitude or have the aircraft climb to the highest minimum altitude in your area of jurisdiction before you issue a heading.

    REFERENCE-

    FAAO JO 7110.65, Para 3-1-9, Use of Tower Radar Displays.

    FAAO JO 7110.65, Para 5-12-11, Surveillance Unusable.

    5-3-3. BEACON IDENTIFICATION METHODS

    When using only Mode 3/A radar beacon to identify a target, use one of the following methods:

    a. Request the aircraft to activate the "IDENT" feature of the transponder and then observe the identification display.

    NOTE-

    1. At facilities where the single-slash "IDENT" modification is installed or other decoder modifications have been made which increase the number of "blooming" target displays, it will be necessary to exercise additional care to preclude the possibility of misidentification.

    2. TERMINAL. When automated displays are operated in the analog mode, the "IDENT" return is displayed as a double slash and the emergency return as a single bloomer whenever the beacon control head is in the "fail" position.

    PHRASEOLOGY-

    IDENT.

    SQUAWK (code) AND IDENT.

    b. Request the aircraft to change to a specific discrete or nondiscrete code, as appropriate, and then observe the target or code display change. If a code change is required in accordance with Section 2, Beacon Systems, of this chapter, use the codes specified therein.

    c. Request the aircraft to change transponder to "standby." After you observe the target disappear for sufficient scans to assure that loss of target resulted from placing the transponder in "standby" position, request the aircraft to return transponder to normal operation and then observe the reappearance of the target.

    PHRASEOLOGY-

    SQUAWK STANDBY,

    then

    SQUAWK NORMAL.

    d. EN ROUTE. During narrowband operations, an aircraft may be considered identified when the full data block is automatically associated with the beacon target symbol of an aircraft that is squawking a discrete code assigned by the computer.

Question Stats

Latest activity: earlier.
This question has 1 answers.

BECOME A GUIDE

Share your knowledge and help people by answering questions.
Unanswered Questions