Why don't we use isoproply alcohol as a fuel for cars instead of ethanol?

Question

Why don't we use isoproply alcohol as a fuel for cars instead of ethanol?

Answer 1

since all alcohols burn, any of them can be used as a motor fuel if you have a 160 minimum proof. if you use an alcohol fuel, ethanol is the one to use since it is renewable, and you will use less ethanol than any other alcohol as it has a higher BTU content than the other alcohols.

Answer 2

I currently run ethanol (corn alcohol) in a 1999 Dodge 3500 truck. But all Cummins engines were modified from the factory to run on BioD since around 1992 without any modification.

Most vehicles are already equipped to run on Alternative Energy. In fact you’re probably even driving one right now and didn’t even know it. Go to www agua-luna com for a list of this vehicles

The following are a couple types of products to make ethanol easily. There are however many materials one can use including sugar cane, corn, wood, etc. The information was cut directly from a guide I offer at www agua-luna com, it is complete but if anyone’s interested in other types of foods to use or a more specific step by step of the process, including building your own still legally, visit www agua-luna com

"THE usual sources of raw material for alcohol Ethanol production from starch are cereal grains such as corn, wheat, rye, barley, milo (sorghum grains), rice, etc. Other types of starch are available from potatoes of all kinds, Jerusalem artichokes, and other high-starch vegetables. Starch conversion is the standard method of production and the one we will discuss here.

It is possible, however, to make alcohol from sugar-producing plants (saccharine material) such as sugar beets, sugarcane, fruits, and others. These substances need no milling (as do grains), but they do require some kind of grinding or squeezing process. Rapid, efficient fermentation of these sugars has not been as well explored as the process using starch.

A third source of fermentables is cellulose, as found in wood and waste sulphite liquor. This more complex process requires the use of acids to reduce the material to wood sugars. Consequently, most do-it-yourselfers should stick to either starch or sugar.

MILLING

All grains must be ground before mashing to expose the starch granules and help them remain in suspension in a water solution. The grain should be ground into a meal -- not a flour! -- that will pass a 20-mesh screen. On a hammermill, however, a 3/16" screen will suffice.

Potatoes and similar high-moisture starch crops should be sliced or finely chopped. Since potato starch granules are large and easily ruptured, it isn't necessary to maintain the hard rapid boil which is required of the tougher, dryer "flinty" starches found in grains.

CONVERSION WITH ENZYMES

For small batches (5 bushels or less), fill the cooker with water (30 gallons per bushel), and add the meal slowly, to prevent lumps from forming. (When, cooking with steam, or at higher temperatures, it is possible to save energy by using less water at the beginning. But for the "small batcher" with an ordinary cooking apparatus, the most complete conversion is obtained by using the full amount of water right from the start to encourage a rapid rolling boil.)

Next, add 3 measuring spoons -- as provided -- per bushel of Alpha Amylase Enzyme (mixed in water) to the mixture and raise the temperature of the mash to 170 deg F (77 deg C), the optimum working environment for the enzyme. Hold the solution at that temperature for 15 minutes while agitating it vigorously.

At this point all the starch available at 170 deg F has been converted to dextrins, so it's time to raise the temperature of the mash to the boiling point. The concoction should be liquid enough to roll at its own rate -- if not, add 2 to 3 gallons of water. Hold the boil for 30 minutes to complete the liquefaction stage. All the starches are now in solution.

Now reduce the temperature to 170 deg F, using the cooling coil, and add 3 more measuring spoons per bushel of Alpha Amylase Enzyme (mixed in water). After 30 minutes of agitation at this temperature, all the previously released starches will have been reduced to dextrins, thereby completing primary conversion.

During secondary conversion the dextrins are further reduced to simple sugars (maltose and glucose) by the beta, or -- to be more exact -- glucoamylase enzymes. You need Alpha Amylase Enzyme and the yeast necessary to carry out secondary conversion and proper fermentation simultaneously, you can add 6 measuring spoons per bushel of the fermentation powder (mixed in water) as soon as you've brought the temperature down to 85 deg F (29 deg C) using the cooling coils."

Hope this helped, feel free to contact me personally if you have any questions if you’d like assistance in making your first self sufficient steps, I’m willing to walk you step by step threw the process. I’ve written several how-to DIY guides available at  www agua-luna com on the subject. I also offer online and on-site workshops, seminars and internships to help others help the environment.

Dan Martin

Alterative Energy / Sustainable Consultant, Living 100% on Alternative & Author of How One Simple Yet Incredibly Powerful Resource Is Transforming The Lives of Regular People From All Over The World... Instantly Elevating Their Income & Lowering Their Debt, While Saving The Environment by Using FREE ENERGY... All With Just One Click of A Mouse...For more info Visit:  

www AGUA-LUNA com

Stop Global Warming, Receive a FREE Solar Panels Now!!!

Answer 3

You can use it directly but sioprophyl alcohol is expensive than gas...

Answer 4

Maybe because you get it from coal and oil? It is not renewable and has a carbon footprint.

I want to know why we don't use methanol, because methanol is very easy to make. Easier than ethanol. Methanol was once proposed as an alternative fuel, but you never hear that any more. Maybe because methanol is toxic while ethanol is not. And maybe because you don't need corn to make methanol so the powerful farm lobby didn't push the program.

Answer 5

It probably burns too hot and is not as explosive a gas.